|
|
 |
 |
| |
| Products » Accessories » ENCLOSURES,
PANELS, TOWERS |
 |
| ENCLOSURES,
PANELS & TOWERS |
| |
MODIFIED STEEL NEMA4 ENCLOSURE
5100-0100

- NEMA Enclosure assembly with 6 water-tight glands installed
- External mounting feet
- Seams continuously welded
- Rolled lip around door to exclude liquids
- Oil resistant gasket
- Hasp and staple for padlocking
- Grey polyester powder coating inside and out
Ordering
5100-0100-1
Enclosure, Nema4, Modified Steel, 24 in. H x 20 in. W x 10 in. D
2251-1496
Unmodified Steel Enclosure, 24" x
20"
8205-0001-1
Enclosure, NEMA4, Steel w/8200 tray; 20
in. H x 20 in. W x12 in. D
XLITE & SATLINK ENCLOSURES
6661-1275 , 6661-1276 SPECIFICATIONS
Both enclosures are 14.13" X 12.26" X 6.13" .
Each includes the following:
2 twist-lock latches with a space for a lock
3 DIN rails to mount optional equipment inside the enclosure such as additional
I/O modules, modems, etc.
Mounting holes for protection boards
3 digital, 4 analog, VREF, SW'D 12, 4 SDI-12, Input Power and a phone line
(RJ to Terminal block) thru terminal blocks.
3 PG-9 and 2 PG-11 plugs
Cable strain relief fittings for additional wires
Single point grounding connector
Additional Specifications Included in 6661-1276-1
GPS and RF-out connections included
RF-out configured so that panel-mounted
Polyphaser Lightning Protection (fits in RF-out and ground connections)
|
|
30
FT TOWER

- Equilateral triangle welded truss design
- Built-in 10-foot lengths, suitable for mounting weather instrument
- Typically includes one top section, a tapered section, a straight section,
and an appropriate base
- Made of aircraft-grade 6063-T832 aluminum tubes and 6061-T6 bracing rods.
- Guyed Tower provides extra strength and stability by adding three 64 in. anchor
rods, wire rope and associated hardware.
30 FT TOWER SPECIFICATIONS
Subject to change without notice
WIND LOAD OF ATTACHMENTS |
Zone A: |
up to 4.5 ft squared |
Zone B: |
up to 2.5ftsquared |
Zone C: |
up to 1.5ftsquared |
FEATURES |
| Height |
30 feet |
| Weight |
8 lb. |
| Tower Cross at Base |
13.5-inch triangle |
| Section at Top |
10.25-inch triangel |
| Material Tubes |
1 in. x 0.0065 wall 6063-T832 |
| Braces |
3/8 in. solid
6061-T6 |
| Construction |
3 sections plus base |
| Base Mount |
Installed in 0.5 to 1 cubic yard of concrete |
ORDERING |
| 5100-0210 |
Tower, 30 ft., Free standing |
| 5100-0220 |
Tower, 30 ft., Guyed |
ACCESSORIES |
| 5100-0600-2 |
Lightning
Protection Kit, Tower |
| 2911-1066-1 |
Mounting
Hardware, Antenna |
| 6211-1012-1 |
Enclosure
Mounting Hardware |
| 2911-1196-1 |
Mounting
Hardware, Tipping Bucket |
| 6661-1098-1 |
Mounting
Kit, Pyranometer |
Other heights are available by
request
Galvanized Steel Towers Available on Request |
|
|
4X FIBERGLASS ENCLOSURE
2251-1556
|
|

TRIPOD TOWER
|
- Highly effective corrosion-resistant housing for electrical & electronic controls
- Provides outstanding protection against atmospheric & marine corrosion in indoor or outdoor settings
- Molded fiberglass-reinforced material - excellent temperature, chemical & high impact resistance
- Easily punched, drilled, filed, or sawed
- Seamless foam-in-place gasket assures watertight and dust-tight seal
- Enclosure may be rotated 180 degrees for left and right hinging
- Molded-in drip shields are standard with each enclosure
- Impact-resistant polycarbonate window is permanently bonded in place
- Fiberglass mounting brackets and stainless steel attachment screws
- Door opens 180 degrees
- Replaceable breakaway hinges
- Patented Type 316 stainless steel quarter-turn latch. Optional keylocking or padlocking handle available
- Molded-in DIN bosses
- Molded bosses on door provide additional mounting provisions
- Integral mounting rails provide infinite panel adjustment front to back
- Optional data pocket is high-impact thermoplastic
- External Dimensions 20.18 "x 16.24"
Internal Dimensions 19.51" x 15.57" x 8.64"
- Finish & Color
Light gray acrylic enamel for enhanced UV protection.
- Industry Standards
UL 508A, 508, File No. E61997:Type 3,Type 3R, Type 4, Type 4X,Type 12, & Type 13
NEMA/EEMAC Type 3,Type 3R,Type 4, Type 4X,Type 12, & Type 13
Enclosure flammability rating per UL 508
CSA File No. LR42186:Type 3,Type 3R, Type 4,Type 4X,Type 12, and Type 13
IEC 60529, IP66
Meets Type 3RX requirements
|
LIGHT-WEIGHT COLLAPSIBLE TRIPOD
FOR RAPID DEPLOYMENT & RETRIEVAL
- Easily transported and erected by a single person
- Supports complement of weather/atmospheric instrumentation weighing <15 lbs. w/winds <90 mph
- Standard 6 ft., no guys required
- Expandable to 10 ft. (Guys should be used.)
- Easily erected by one person
- Free standing in winds up to 30 mph.
-
Easily installed foot pad anchors
APPLICATIONS
» Mounting wind instruments
» Antenna tower
» Temporary/portable installations
SPECIFICATIONS
WEIGHT 15 lbs.
LENGTH 48 in. (collapsed)
HEIGHT 6 ft. or telescoping to 10 ft. (erected)
MOUNTING Mast top - dia. of 3/4 in. water pipe
& fits most cross-arm clamps. Other
members - 15/16 in. dia.
MATERIALS Epoxy painted aluminum
ORDERING
5100-0209 Tower, 6 ft. (expandable to 10 ft.)
ACCESSORIES
5100-0208 Crossarm Assy, Wind Sensor
IMPORTANT INFORMATION
Special care is required during installation. All tower BASES must be set in concrete before the tower is assembled & raised to an upright position.
CONCRETE SHOULD BE ALLOWED TO
SET 3-4 DAYS BEFORE THE TOWER IS ERECTED.
Aluminum tower SECTIONS should NEVER BE PLACED DIRECTLY IN CONCRETE!
The corrosive effects of cement can destroy aluminum tower sections.
Use ONLY THE BASES provided with the tower.
Tower SECTIONS also REQUIRE DRAINAGE to minimize the possibility of freezing and splitting. The base provided allows the tower to drain properly to minimize possibility of damage.
INSTALLATION OF A TOWER WITHOUT THE PROPER BASE VOIDS ALL WARRANTIES.
|
|
| |
|
|
|